Campbell-scientific TD Operating System Addendum for CR510, CR10X, and Bedienungsanleitung

TD OPERATING SYSTEM ADDENDUM FOR CR510, CR10X,AND CR23X MANUALSREVISION: 1/03COPYRIGHT  2002-2003 CAMPBELL SCIENTIFIC, INC.

TD ADDENDUM—OVERVIEWAD-OV-2TABLE OV4.2-2. Additional Keys Allowed inTelecommunicationsKey Action- Change Sign, Index (same as C) CR Enter/advance (sa

TD ADDENDUM—OVERVIEWAD-OV-3location 5, the temperature from channel 2 in inputlocation 6, etc.Detailed descriptions of the instructions aregiven in Se

TD ADDENDUM—OVERVIEWAD-OV-4Key (ID:Data) Explanation*0 LOG 1 Exit Table 1, enter *0 Mode, compile table and beginlogging. *6 06:0000 Enter *6 Mode (to

TD ADDENDUM—OVERVIEWAD-OV-5OV5.2 SAMPLE PROGRAM 2This second example is more representative of areal-life data collection situation. Once again thei

TD ADDENDUM—OVERVIEWAD-OV-6SAMPLE PROGRAM 2Instruction # Parameter(Loc:Entry) (Par#:Entry) Description*1 Enter Program Table 101:60 60 second (1 minut

TD ADDENDUM—OVERVIEWAD-OV-7The program to make the measurements and send the desired data to Final Storage has beenentered. The program is complete.

TD ADDENDUM—OVERVIEWAD-OV-8DATALOGGERMD9MULTIDROPINTERFACERF95 RFMODEMSC932INTERFACECOM210PHONEMODEMRF100/RF200TRANSCIEVERW/ ANTENNA& CABLESC32ARS

AD-1-1SECTION 1. FUNCTIONAL MODESSections 1.5 and 1.8 are replaced by the following sections.1.5 MEMORY ALLOCATION - ∗A1.5.1 INTERNAL MEMORYWhen po

TD ADDENDUM  SECTION 1. FUNCTIONAL MODESAD-1-2FIGURE 1.5-1. Datalogger Memory1.5.2 ∗A MODEThe ∗A Mode is used to 1) check the size of InputStorage

TD ADDENDUM  SECTION 1. FUNCTIONAL MODESAD-1-3TABLE 1.5-2. Description of ∗A Mode DataKeyboard DisplayEntry ID: DataDescription of Data∗ A01: XXXX

This is a blank page.

TD ADDENDUM  SECTION 1. FUNCTIONAL MODESAD-1-4to which memory is cleared on powerup, to setthe PakBus ID, and to set communication to fullor half du

TD ADDENDUM  SECTION 1. FUNCTIONAL MODESAD-1-51.8.6 SET INITIAL BAUDTable 1.8-10 shows the option codes availablefor setting the initial baud rate.

TD ADDENDUM  SECTION 1. FUNCTIONAL MODESAD-1-6The *D15 entries are sent when the program isretrieved. They can also be set like other *Dsettings vi

TD ADDENDUM  SECTION 1. FUNCTIONAL MODESAD-1-7TABLE 1.8-14. Set PakBus NeighborsKeyEntry DisplayComments*D 13:00 Enter Command19A 19:00 Port (17- S

TD ADDENDUM  SECTION 1. FUNCTIONAL MODESAD-1-8This is a blank page.

THIS SECTION ENTIRELY REPLACES THE DATALOGGER MANUAL SECTION 2.AD-2-1SECTION 2. INTERNAL DATA STORAGE2.1 FINAL STORAGE AND DATATABLESFinal Storage i

TD ADDENDUM—SECTION 2. INTERNAL DATA STORAGEAD-2-2• The output interval is not an even multipleof the scan rate (table execution interval).• Table e

TD ADDENDUM—SECTION 2. INTERNAL DATA STORAGEAD-2-3The Timestamp and record number labels areadded automatically.2.2 DATA OUTPUT FORMAT ANDRANGE LIMI

TD ADDENDUM—SECTION 2. INTERNAL DATA STORAGEAD-2-4TABLE 2.3-1. *7 Mode Command SummaryKEY ACTIONA "Advances" along a record, when theend of

AD-3-1SECTION 3. INSTRUCTION SET BASICSSection 3.7.1 does not apply to the TD operating system which does not use Output Flag 0.Table 3.8-1 Valid Fla

TABLE DATA ADDENDUMAD-1TD and PakBus Operating System Addendum forCR510, CR10X, and CR23X ManualsAD1 Major DifferencesTable Data (TD) operating system

TD ADDENDUM—SECTION 3. INSTRUCTION SET BASICSAD-3-294 Program Program Storage AreaTransfer full95 Program Program does not exist inTransfer Flash mem

THIS SECTION ENTIRELY REPLACES THE CR10X MANUAL SECTION 8.AD-8-1SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLESThis section contains examples for

TD ADDENDUM—SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLESAD-8-205: P84 Data Table 01: 0 Seconds into interval 02: 0 Every time 03: 0 Records (0=

TD ADDENDUM—SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLESAD-8-303: P92 If time is 01: 0 seconds into a 02: 900 second interval 03: 11 Set high F

TD ADDENDUM—SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLESAD-8-4FIGURE 8.3-1. AM416 Wiring Diagram For Thermocouple and Soil Moisture Block Meas

TD ADDENDUM—SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLESAD-8-58.4 INTERRUPT SUBROUTINE USEDTO COUNT SWITCH CLOSURES(RAIN GAGE)Subroutines give

TD ADDENDUM—SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLESAD-8-68.5 SDM-A04 ANALOG OUTPUTMULTIPLEXER TO STRIP CHARTThis example illustrates the

TD ADDENDUM—SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLESAD-8-710: P69 Wind Vector 01: 1 Rep 02: 180 Samples per sub-interval 03: 0 Polar Sensor

TD ADDENDUM—SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLESAD-8-8Time into Test, min Output Interval Loop #00 to 10 10 sec. 110 to 30 30 sec. 230

TD ADDENDUM—SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLESAD-8-9Loop 6, Output every 10 minutes until stoppedby user17: P87 Beginning of Loop 01:

TABLE DATA ADDENDUMAD-2AD2 Overview of Data Storage TablesWithin a data table, data is organized in records and fields. Each row in atable represent

TD ADDENDUM—SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLESAD-8-10This is a blank page.

AD-9-1SECTION 9. INPUT/OUTPUT INSTRUCTIONS*** 18 MOVE TIME TO INPUT LOCATION ****FUNCTIONThis instruction takes current time or dateinformation and d

This is a blank page.

AD-11-1SECTION 11. OUTPUT PROCESSING INSTRUCTIONSInstructions 73 – Maximum and 74 – Minimum have only one time option. (Time is output as a quotedst

TD ADDENDUM—SECTION 11. OUTPUT PROCESSING INSTRUCTIONSAD-11-2records. If 0 is entered, records will beautomatically allocated such that all automatic

12-1Section 12. Program ControlInstructionsThe TD operating system does not use the output Flag 0. Commands dealing with it arenot valid.Instruction

Section 12. Program Control Instructions12-2TABLE 12-1. CR205/CR210/CR215 in PakBus NetworkStand AloneDatalogger SendGetData P190 Wireless Sensor P1

Section 12. Program Control Instructions12-3Stand AloneDatalogger SendGetData P190 Wireless Sensor P193Radio SettingsRadio address, net address, and

Section 12. Program Control Instructions12-4Notes: Edlog allocates only one of the input locations used in parameters 5 and 7 ofthis instruction. The

Section 12. Program Control Instructions12-5PakBus CommunicationThe unique address for the datalogger in the PakBus network that will becommunicated

TABLE DATA ADDENDDUMAD-3• Check the Maximum and Minimum Instructions (Instructions 73and 74) as there is only one option to store time with the value.

Section 12. Program Control Instructions12-6desirable to delay execution of subsequent instructions if those instructionsperform further processing o

Section 12. Program Control Instructions12-7Remote LocationPakBus CommunicationIf data is being received from another datalogger in the PakBus networ

Section 12. Program Control Instructions12-8or unpacked with the least significant bit of the first byte, starting at thislocation. Incoming discrete

Section 12. Program Control Instructions12-9This instruction is not necessary in networks with wireless sensors and onlyone Master datalogger, becaus

Section 12. Program Control Instructions12-10Edlog allocates only one of the input locations used in parameters 7, 9, and 10of this instruction. The

Section 12. Program Control Instructions12-11ExampleTo set up the remotes for an hourly transmission at 15 minutes past the hour,the Time into Transm

Section 12. Program Control Instructions12-12For general information on input locations, see Input Locations. Swath to SendThe number of data values

Section 12. Program Control Instructions12-13Location with Seconds Until TransmitThe input location in which to store the number of seconds until it

Section 12. Program Control Instructions12-14Swath to Receive From MasterThe number of data values that will be received from the host (master)datalo

Section 12. Program Control Instructions12-15For general information on input locations, see Input Locations. Result Code LocationThe input location

TABLE DATA ADDENDUMAD-4AD4 Summary of Differences from the Datalogger Manual:SectionDifferencesOverviewFigure OV2.1-2: See Figure 1.5-1 in Addendum.T

Section 12. Program Control Instructions12-16Result LocationResult Code Description-1001 The attempted setting is a read-only setting-1002 Out of spa

Section 12. Program Control Instructions12-17The information returned using this instruction would be similar to:InputLocationUsedValueStored Descrip

Section 12. Program Control Instructions12-18desired interval in the Communications Interval field. This option is the sameas the datalogger's *

TABLE DATA ADDENDDUMAD-5Section 12The TD operating system does not use the output Flag 0.Commands dealing with it are not valid.Instruction 92 – There

TABLE DATA ADDENDUMAD-6This is a blank page.

AD-OV-1MEASUREMENT AND CONTROL MODULE OVERVIEWWhile this section of the addendum references the CR10X, everything but the measurement instructionsin t